← Blog

Why Is My Roller Shade Rolling Crooked? Causes and Fixes for Telescoping

Wednesday, November 4, 2026 — Wholesale Blind Factory

A roller shade that drifts sideways as it rolls up, leaving the fabric edge sticking out past the tube, is "telescoping". It is almost always caused by the shade being slightly out of square, the brackets being out of level or alignment, or the fabric rolling onto the tube unevenly, and most cases can be fixed or at least improved without replacing the shade. Here is how to work out which cause you have and what to do about it.

What telescoping looks like

When a roller shade is rolled up, the fabric should wind onto the tube in a neat, flat spiral with the edges lined up. Telescoping is when each turn creeps a little further to one side, so the roll looks like a cone or a stack of shifted layers. You may see the fabric edge rub against the bracket, the side of the headrail or the window frame, and in bad cases the shade will jam or stop rolling smoothly.

A small amount of drift, a few millimetres over the full drop, is common and normal. It becomes a problem when the edge is rubbing, the shade is hard to operate, or the fabric is getting scuffed or frayed.

The most common causes

1. Brackets that are not level or not parallel. If one bracket sits a few millimetres higher than the other, or one is set further out from the wall than its partner, the tube is tilted and the fabric wanders toward the low side. This is the cause we see most often on DIY installs and on windows where the frame itself is not perfectly square.

2. A window opening that is out of square. Older homes, and plenty of newer condos, have frames that are not truly square or plumb. Brackets screwed into a crooked frame will faithfully reproduce the crookedness. A level checks the brackets; a tape measure across both diagonals tells you if the opening itself is the issue.

3. Uneven tension from the spring or the chain mechanism. If the shade is pulled sharply to one side, the fabric can start rolling crooked, and once it starts it tends to continue.

4. Fabric that is not cut perfectly square to the tube. This is a manufacturing point. At a factory the fabric is cut and attached to the tube with great care, because a fabric edge that is off by even a small angle will telescope every time. If the shade telescoped from the day it was installed, and the brackets and window are square, this is the likely cause and it is a warranty conversation, not a DIY one.

5. Wide, heavy or thick fabrics. The wider the shade and the thicker the fabric, the more any small imperfection is magnified as the roll gets larger. Blackout and heavily backed fabrics build up faster on the tube than thin ones.

How to check and fix it yourself

  1. Roll the shade fully down, then up, and watch. Note which side the fabric drifts toward. That is usually the lower or looser side.
  2. Check the brackets with a small level. Both brackets should be at the same height and the same distance from the wall or frame. If one is off, loosen it, adjust and retighten.
  3. Check the tube sits fully and evenly in both brackets. A tube that is not seated all the way into one bracket tilts slightly.
  4. Let the shade down and re-roll it by hand. Lower the shade to its full length, then roll the tube back up gently by hand with the fabric edges aligned, keeping steady tension. Sometimes this resets a roll that started crooked.
  5. Use a thin shim. If the bracket cannot be moved, a thin shim or washer behind one bracket can correct a few millimetres of tilt. Make small changes and test after each one.
  6. Recheck after a week. Fabric and spring tension settle, so a shade that seems fine right after adjustment is worth a second look.

If the shade is motorized, the limits and the motor speed matter too. A motor that rolls the shade at a steady speed usually tracks better than a hand-pulled chain. If you have a Somfy motor and the drift continues after the brackets are corrected, ask us to check the motor settings rather than forcing it.

When it is not a DIY fix

Some telescoping cannot be corrected at the window:

Preventing it on a new order

Most telescoping is decided at measuring and installing, not afterwards:

Not sure which cause you have?

If you have tried the checks above and the shade still drifts, or if it is a recent shade and you suspect a manufacturing problem, get in touch. Bring a photo of the rolled-up shade and tell us the width. In many cases we can say what is happening from a picture, and if it needs a visit or a factory look we will tell you plainly. Our free in-home consultation and our repair service cover both.